Select your country

Country: Germany
Languages:

Headquarters: SIKO GmbH Weihermattenweg 2 79256 Buchenbach Germany Phone+49 7661 394-0 info@siko-global.com

Absolute encoder WV3600MR

Magnetic safety rotary encoder with solid shaft

open expert video

The smallest safety multiturn rotary encoder for mobile machines! Specially developed for use in mobile machines, the absolute safety rotary encoder WV3600MR provides reliable and precise measured values even under the toughest environmental conditions. Thanks to the innovative safety concept, certified according to SIL2, the WV3600MR can also be used in safety-critical applications up to performance level d. Available as a singleturn and multiturn version and with an outer diameter of only 36 mm, it can also be mounted in applications with extremely limited installation space.

Profile WV3600MR:

Smallest safety multiturn rotary encoder for mobile machines
Single turn or multiturn variant available
SIL2 (IEC 61508) PLd (DIN EN ISO 13849) certified (in preparation)
E1 approval by the German Federal Motor Transport Authority (KBA) pending
Protection class up to IP6K9K
With PURE.MOBILE technology

Inquire about product/Add to leaflet

Mechanical data

Feature	Technical data	Additional information
Shaft	rustproof stainless steel
Flange	aluminum
Housing	rustproof stainless steel
Speed	≤3000 rpm	with protection classes IP67 and IP6K9K
	≤6000 rpm	with protection class IP65
Moment of inertia	<3.5 gcm²	with protection class IP67
	<4 gcm²	with protection class IP6K9K
Starting torque	≤2 Ncm at 20° C
Shaft load rating	≤60 N	radial
	≤40 N	axial
	≤200 N	radial, with protection class IP6K9K
	≤200 N	axial, with protection class IP6K9K

Electrical data

Feature	Technical data	Additional information
Operating voltage	8 … 36 V DC	reverse-polarity protected
Power input	≤1 W	at 36 V, without load
Parameter storage	10⁵cycles	also applies to calibration operations
Status display	1x two-color LEDs (red/green)	device / CAN status
Power rating	±36 V	CAN interface
Interface	according to ISO 11898-1, not electrically isolated	CANopen
	according to ISO 11898-1, not electrically isolated	CANopen Safety
	according to ISO 11898-1, not electrically isolated	SAE J1939 Safety
Address	1 … 127	CANopen, CANopen Safety
Baud rate	20 kbit/s	CANopen Safety
	50 kbit/s	CANopen Safety
	125 kbit/s	CANopen Safety
	250 kbit/s	CANopen Safety
	500 kbit/s	CANopen Safety
	800 kbit/s	CANopen Safety
	1 Mbit/s	CANopen Safety
Cycle time	<10 ms
Starting time	<1000 ms
Parameter	according to CiA 301, CiA 303 Part 3, CiA 305, CiA 406 EN 50325-5	CANopen Safety
Type of connection	1x M12 connector (A-coded)	5-pole, 1x pin (E12E connection type)
	open cable end	stranded wire cross-section 0.5 mm² ( E1 connection type)

System data

Feature	Technical data	Additional information
Scanning	magnetic
Resolution	14 bit	singleturn, 16384 steps/rotation
Measuring range	1 revolution(s)	singelturn
	4096 revolution(s)	12 bit
	65536 revolution(s)	16 bit

Ambient conditions

Feature	Technical data	Additional information
Ambient temperature	-40 … +85 °C
Storage temperature	-40 … +85 °C
Relative humidity	100 %	condensation permitted
Protection category	IP65	EN 60529
	IP67, IP6K9K	EN 60529, ISO 20653, according to assembly instructions and with suitable mating connector
	IP6K9K	ISO 20653
Salt spray test	severity level 4	EN 60068-2-52, verbaut nach Montageanleitung und mit geeignetem Gegenstecker

Pin assignment

E12E

Signal	PIN
nc	1
+UB	2
GND	3
CAN_H	4
CAN_L	5

E1

Signal	Cable color E1
nc	white
+UB	brown
GND	green
CAN_H	yellow
CAN_L	gray

Scope of delivery

WV3600MR
Quick Start Guide

Ordering table

Feature	Order data	Specifications	Additional information
Number of revolutions	A1	singleturn
	4096	12 bit
	65536	16 bit

Shaft diameter x length	B10x20	ø10 mm x 20 mm
	6x10	ø6 mm x 10 mm
	N3/10x20	ø10 mm x 20 mm, feather key
	S4/10x20	ø10 mm x 20 mm, grooved pin

Mounting type	CM1	supported flange joint ø58 mm
	M2	servo flange ø58 mm
	M3	supported flange joint ø36 mm
	M4	servo flange ø36 mm

Protection category	DIP65	IP65
	IP67	IP67
	IP6K9K	IP6K9K	only with shaft diameter 10 and mounting type M4

Position of electrical connection	EA	axial
	R	radial

Type of connection	FE1	open cable end
	E12E	Bus IN

Cable length	GOK	without cable	only with type of connection E12E
Cable length	...	01.0, 02.0, 03.0, 05.0, 10.0 in m	only with type of connection E1