Signal | EX | E1 |
---|---|---|
+ | 1 | M1, white imprinted |
+ | 2 | |
- | 3 | M2, white imprinted |
- | 4 |
Headquarters: SIKO GmbH Weihermattenweg 2 79256 Buchenbach Germany Phone+49 7661 394-0 [email protected]
Feature | Technical data | Additional information |
---|---|---|
Shaft | black-finished steel | |
Housing | aluminum, powder coated zinc die cast | |
Nominal torque/rated speed | 1.1 Nm at 430 rpm | i = 12.4 (70 W motors) |
2.1 Nm at 225 rpm | i = 24 (70 W motors) | |
4.2 Nm at 110 rpm | i = 48 (70 W motors) | |
Operating mode | S3 intermittent operation: 25 % DC, 10 min. | EN 60034-1 |
Weight | ~1.5 kg |
Feature | Technical data | Additional information |
---|---|---|
Operating voltage | 0 … 24 V DC | 70 W motors |
Power input | 70 W | |
Rated current | 2.9 A ±10 % (70W-M) | 3.2 A max. load current |
4.1 A ±10 % (70W-G) | 4.5 A max. load current | |
Type of connection | 2x M9 plug connectors | 4-pole, 1x pin; 3-pole, 1x pin |
2x M9 plug connectors | 4-pole, 1x pin; 8-pole, 1x pin |
Feature | Technical data | Additional information |
---|---|---|
Operating voltage | 5 V DC ±5 % | LD5 position encoder |
24 V DC ±20 % | LD24 + OP position encoder | |
Current consumption | ≤35 mA | |
Output circuit | Line Driver (RS422) | LD5 + LD24 position encoders |
Push Pull (OP) | OP position encoder | |
Output signals | A, B, 0, /A, /B, I | |
Pulse frequency | ≤20 kHz |
Feature | Technical data | Additional information |
---|---|---|
Power rating | 2 W at 70 °C | P10 position encoder |
Resistance tolerance | ±5 % | P10 position encoder |
Standard terminal resistance | 0.2 % or 1 Ω | P10 position encoder (always the higher value) |
Linearity tolerance | ±0.25 % | P10 position encoder |
Feature | Technical data | Additional information |
---|---|---|
Operating voltage | 24 V DC ±20 % | at ≤500 Ω load |
Feature | Technical data | Additional information |
---|---|---|
Operating voltage | 24 V DC ±20 % | ILoad ≤10 mA |
Feature | Technical data | Additional information |
---|---|---|
Ambient temperature | 0 … 70 °C | |
0 … 80 °C | without position encoder | |
Storage temperature | -20 … 80 °C | |
Relative humidity | condensation inadmissible | |
EMC | EN 61800-3, second environment | interference resistance / immission |
EN 61800-3, C3 | emitted interference / emission | |
Protection category | IP63 | EN 60529, with mating connectors mounted |
Shock resistance | 500 m/s2, 11 ms | EN 60068-2-27 |
Vibration resistance | ≤100 m/s2, 5 ... 150 Hz | EN 60068-2-6 |
Feature | Order data | Specifications | Additional information |
---|---|---|---|
Gear ratio | A48 | i = 48 | |
24 | i = 24 | ||
12.4 | i = 12.4 | ||
Motor performance | B70W-M | 24 V DC | |
70W-G | 24 V DC | ||
others on request | |||
Shaft design/diameter | CKR/14 | clamping ring, ø14 mm | |
KR/12 | clamping ring, ø12 mm | ||
N/10 | keyway | only for type S hollow shaft | |
Hollow shaft type | DS | blind hole | |
D | full-length | ||
Torque pin | EA | bolt, ø6 mm | |
B | lug I | incl. elastomer bushing | |
Type of connection | FE1 | open cable | |
EX | socket on the device | ||
Motor cable length | G02.0 | in m | |
others on request | |||
Encoder cable length | H02.0 | in m | |
others on request | |||
Position encoder | ILD24 | incremental encoder 1024 pulses | |
LD5 | incremental encoder 1024 pulses | ||
OP | Push-pull with inverting | ||
O | without | ||
additional accessories | Ordering key |
---|---|
Mating connector, motor, 4-pole, socket | 83447 |
Mating connector, encoder, 8-pole, socket | 81351 |